Skip to main content
Esc

Parts List for the Blueprint Builds

By Jordan Stambaugh · Last updated October 30, 2026

This page lists every line of the three bills of materials in The DIY Off-Grid Solar Blueprint. A line links to a product only when my catalog has one that really fits its voltage and capacity. That is 5 of 30 lines. The rest stay as the spec to shop for, because a wrong-voltage link is worse than no link on a purchase this size.

I have not tested any of these products. Matches come from published specs, and catalog prices are indicative, so check the retailer before you buy. Run your own load audit first, since these are reference builds and your numbers decide what you need. The power calculator and solar sizing calculator are a quick way to check them.

Build A: The Weekender

12 V · 400 W · 2.56 kWh

About 950 Wh a day. Camp cabin, van or backup kit. This is the build the catalog covers best, because 12 V panels, controllers and batteries are what most of it holds. The inverter is the gap.

Parts total in the Blueprint: $1,650 to $2,450, from U.S. retail prices seen in September 2026, before tax, shipping and tools.

  • Solar panels

    2 × 200 W rigid mono, 12 V class, wired in series

    Buy two identical panels. Either pair below stays far under a 100 V controller limit, about 46 V before the cold-weather correction.

  • Charge controller

    Victron SmartSolar MPPT 100/30 or equivalent: 100 V input, 30 A output

  • Battery

    12.8 V 200 Ah LiFePO4: one 200 Ah battery, or two 100 Ah in parallel

    All three list a 32°F low-temperature charge cutoff, so plan around that if the bank sits in an unheated space.

  • Inverter

    1,000 W pure sine, 12 V, low idle draw

    No catalog match. The smallest 12 V pure sine inverter I list is 2,000 W, which can pull about 185 A. Build A's 125 A fuse and 2 AWG inverter run are sized for 1,000 W, so it is not a drop-in swap.

  • Battery monitor

    Victron SmartShunt 500 A

  • Main fuse

    150 A Class T fuse with insulated holder

  • Disconnects

    Battery switch, plus a 20 A DC PV breaker rated 150 VDC or higher

  • Distribution

    Busbars, DC fuse block, branch fuses

  • Wire and terminations

    1/0, 2, 8 and 10 AWG, PV wire, MC4 connectors, tinned lugs, heat shrink

  • Mounting

    Roof or rack mounts, backer board, strain reliefs

Build B: The Cabin / RV

24 V · 1,200 W · 5.12 kWh

About 3 kWh a day. Part-time living with generator backup. Two lines match here, and both come with conditions. Read the notes before buying, because each one changes something in the build.

Parts total in the Blueprint: $3,500 to $5,400, from U.S. retail prices seen in September 2026, before tax, shipping and tools.

  • Solar panels

    3 × 400 to 415 W rigid mono, wired in series. The Blueprint's worked example uses Voc 37.1 V and Isc 13.9 A.

    No catalog match at this budget. The one 400 W rigid panel I list costs several times the Blueprint's $0.33 to $0.45 per watt, and its published Voc differs between sources. Whatever you buy, run the cold-weather voltage check with the Voc on that panel's label.

  • Charge controller

    Victron SmartSolar MPPT 150/45: 150 V input, 45 A output

    No catalog match. Do not substitute a 100 V controller: the Blueprint's three-panel string reaches about 127 V at −30°C, and every other MPPT I list tops out at 100 V. The Victron 150/35 has the voltage but is listed at 1,000 W on 24 V, short of this 1,200 W array.

  • Battery

    25.6 V 200 Ah LiFePO4 (5.12 kWh)

    I list no 24 V battery. Two 12.8 V 200 Ah batteries in series give the same 25.6 V and 200 Ah. The catalog marks both models below as series-capable, but the Blueprint's rule still applies: use a matched pair, confirm the maker allows series use in its manual, and never tap 12 V from the middle of the string. The DC-DC converter below handles 12 V loads.

  • Inverter-charger

    Victron MultiPlus-II 24/3000 120 V

    • 1 × Sigineer 3000W 24V Inverter-Charger

      Listed as 24 V input, 3,000 W continuous, 120 V output with a transfer switch. 2-year warranty and no Bluetooth or Wi-Fi. Sources disagree on its surge and charger ratings, so check the data plate for the unit you buy.

      Catalog price each: $600

    The Blueprint's MultiPlus-II figure is about 2,400 W continuous, or 111 A. At a full 3,000 W the Sigineer draws 3,000 ÷ (24 × 0.9) = 139 A. Add the 15 A DC-DC load and multiply by 1.25, and the main circuit needs about 193 A, more than the 175 A Class T and 2/0 cable on Plate 05. That points to a 200 A Class T on 3/0 AWG, subject to the inverter manual. The Victron MultiPlus I list is the 12 V model, so it does not fit this 24 V bus.

  • Battery monitor

    Victron SmartShunt 500 A

  • Main fuse

    175 A Class T with a holder rated for the current. See the inverter-charger note if you use a larger inverter.

  • Disconnects

    Battery switch, plus a 25 A DC PV breaker rated 150 VDC or higher

  • DC-DC converter

    24 V to 12 V, about 30 A, for 12 V loads

  • AC distribution

    120 V subpanel, breakers, GFCIs, generator inlet

  • Wire and terminations

    2/0, 6 and 10 AWG, PV wire, lugs, conduit

  • Mounting

    Roof or ground racking for 3 panels

Build C: The Homestead

48 V · 4,800 W · 15.4 kWh

About 9 kWh a day. Full-time off-grid home with a 240 V well pump. Nothing in my catalog is a fair match for this build, so this section links no products. Every line is the spec to shop for.

Parts total in the Blueprint: $9,700 to $13,800, from U.S. retail prices seen in September 2026, before tax, shipping and tools.

  • Solar panels

    12 × 400 to 440 W rigid mono, often sold by the pallet

    No catalog match. Twelve panels at the price of the one 400 W rigid panel I list would far exceed this line's budget. Solar distributors selling by the pallet are the right place to shop.

  • All-in-one inverter

    EG4 6000XP: 6 kW, 2 MPPT inputs, 480 V PV max, split phase

    No catalog match. This build needs 120/240 V split phase for the well pump. The Growatt SPF 5000 ES is smaller at 5 kW, and its manual lists 230 V, 50 Hz output. The PowLand 12000W is twice the size this build's 175 A fuse and 2/0 cable were sized for.

  • Batteries

    3 × EG4 LifePower4 48 V 100 Ah rack modules (UL 1973/9540)

    No catalog match. I list no 48 V rack batteries, and a series string of 12 V batteries would lose the closed-loop communication with the inverter that this design relies on.

  • Rack and bus

    Server rack or cabinet, bus box or busbars, comms cable

  • Main protection

    175 A Class T plus a DC disconnect, or a listed breaker box

  • PV side

    2 PV disconnects rated 600 VDC or higher, PV wire, conduit, MC4 connectors

  • AC side

    Main panel and breakers, generator inlet, ground rod and clamp

  • Ground-mount racking

    12-panel kit, or DIY steel or timber depending on the site

  • Monitoring

    Battery and all-in-one app is built in. A shunt is optional.

Before you wire anything

  • Your equipment manual and local code outrank this list and the Blueprint. If a manual calls for a different fuse or cable, follow the manual.
  • In most of the U.S., a permanent system on a dwelling or outbuilding needs an electrical permit, and your local authority decides which NEC edition applies. Call them before you buy.
  • Hire a licensed electrician for anything you are not sure about. For Build C, that includes the main panel and the 240 V well pump circuit.
  • Any change to an inverter, controller or panel changes the fuse, wire and string math. Rerun it for the parts you actually buy. Series vs parallel panel wiring and series vs parallel battery wiring cover the basics.

Keep shopping

Browse the catalog by category: solar panels, charge controllers, batteries and inverters. New to this? Start with the free DIY solar system guide. The source for the Growatt output rating is the SPF 5000 ES user manual.